Tools/Maintenance

Attractive, durable foam-lined zipper carry case. Perfect for protecting your tool and keeping your bits within easy reach. 12 of the most common Bit sizes for bicycles are included. Weather-resistant case materials and impact protection make this the perfect case to add to your toolset-to-go. A complete pocket multi-tool! Grab the red handle and tighten or loosen screws and bolts all over your bike. The Patented reversible thumb-wheel ratchet head is rated to up-to 60Nm of total force, so this tool can even be used to install and remove Pedals. Tighten each bolt to exact torque! When tightening, finish by pushing on the end-knob. As you tighten, the arrow on the knob will point to the current torque. When the arrow reaches the correct torque, stop tightening. You're done! A high quality, durable tool. Prestacycle TorqRatchet is compatible with all tool bit sets from Prestacycle and all standard ¼" bits. The patented Ratchet head firmly holds bits in place without a magnet. Releasing the bit is simple with a finger-press into the hole on the top. The ratchet offers an easy to use thumb wheel to speed screw installation and removal. The ratchet reverse knob is easily accessible right on top of the tool. The Patent pending Beam torque wrench hidden and protected inside the handle uses hardened alloyed steel and is rated in excess of 5000 cycles and can be re-calibrated by Prestacycle. Specifications - Carry-along pocket Ratchet with 1/4" bits set - 2~10Nm Torque Wrench all in the same tool! - Remove and install all kinds of Bolts and Screws on your Bike. - Finish tightening by pushing the Torque Knob until the arrow reaches your torque - Patented Reversible Ratchet with thumb wheel - Heavy-duty design withstands up to 60Nm of force - Torque scale on Both sides for upside-down use - Uses standard 1/4" Hex bits of all sizes - Calibrated accurate for over 5000 cycles of Torque tightening - Dimensions 5.25" x 11/16" x 7/16" (133mm x 17mm x 12mm) - Tool weight is only 68 Grams! - 12 piece Professional Bicycle Tool Bits set - Precision tools in 12 unique sizes specific for bicycles - S2 Nickel-plated Hardened steel bits are non-marring on titanium and alloy bolts Sizes: Hex: 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm TORX®: T10, T20,T25, T30 Screwdrivers: PH1

Removes and installs crank caps on Shimano® Hollowtech II® cranks. Includes built in hook to lift the safety plate, speeding crank removal. Steel, investment cast body provides good leverage and includes an option to use with an 8mm hex wrench for removing seized caps.

The 4th edition of the Big Blue Book of Bicycle Repair is updated with the latest information, procedures and techniques and covers everything from minor adjustments to complete overhauls. The BBB-4 features clear, step-by-step instructions, high quality color photos and useful charts and graphs to thoroughly explain and demonstrate hundreds of repairs. Written by one of the world’s leading authorities on bicycle repair and maintenance, Park Tool Director of Education, Calvin Jones, the Big Blue Book is the perfect reference guide for nearly any level mechanic and every bike. New information and topics included in the BBB 4th edition: - 12-speed and 1x drivetrains - Tubeless tires - Disc brakes - Electronic shifting - New wheel building content - Updated headset and bottom bracket standards - Updated torque specifications - Updated troubleshooting tables

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Shimano, SRAM GXP, Chris King, Campagnolo, and many others. The BBT-69.3 can also be used to remove and install 16-notch disc brake rotor lockrings. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. The BBT-69.3 features integrated threads for full compatibility with the Park Tool BBT-RS Bottom Bracket Tool Retaining System (sold separately). The BBT-RS uses an adjustable spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. - Fits 16-notch tool fittings with a major diameter (outside of notches) of 44–45 mm and a minor diameter (inside of notches) of 42.7 mm, including: - Shimano BB80, BB5700, XT BB70, BB51, and previous external bearing threaded cups - Threaded bottom bracket cups from Campagnolo, Chris King, FSA MegaExo, Hope, SRAM/Truvativ GXP, Race Face X-type, Surly, Wheels, Fulcrum, and others - 16-notch disc brake rotor lockrings - 16-notch Bafang BBSH, BBS02 mid-drive motor lockrings - 3/8" drive fitting

A precision CNC-machined aluminum tool for the installation and removal of select components with 16-notch tool fittings, including bottom brackets, center lock disc brakes, and e-bike motor lockrings. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. The BBT-69.4 features integrated threads for full compatibility with the Park Tool BBT-RS Bottom Bracket Tool Retaining System (sold separately). The BBT-RS uses an adjustable spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. Fits 16-notch tool fittings with a major diameter (outside of notches) of 44–45 mm and a minor diameter (inside of notches) of 42.7 mm, including: - Shimano BB80, BB5700, XT BB70, BB51, and previous external bearing threaded bottom bracket cups - Threaded bottom bracket cups from Campagnolo, Chris King, FSA MegaExo, Hope, SRAM/Truvativ GXP, Race Face X-type, Surly, Wheels, Fulcrum, and others - Center lock disc brake rotor lockrings - Bafang BBSH, BBS02 mid-drive motor lockrings - 3/8" drive fitting

Bio ChainBrite Bicycle Chain and Component Cleaning Fluid is a 100% biodegradable, natural, plant-based degreaser formulated for use in Park's CM-5.2 Cyclone Chain Scrubber or as a general purpose degreaser. It won't harm alloy, plastic, or rubber parts. Use CB-4 full strength, do not dilute with water. Cover parts in solvent and scrub using a brush. 16-ounce bottle

Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.

Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.

The double-ended HCW-18 spanner fits slotted adjusting cones found on some one-piece cranks. The opposite end fits three-notched fixed-cones on some one piece cranks.

Park's Bottom Bracket/Cassette Tool for Campagnolo is an indispensable tool for your Campagnolo drivetrain. It's for installing and removing all Record, Chorus, Centaur and Athena bottom brackets, and all Campagnolo cassette lockrings.

Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent

A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Park's FR-5 Cassette Lockring Tool fits most cassette lockrings from Shimano, SRAM, SunTour, Chris King, and SunRace. Made from heat-treated tool steel, the FR-5 features an extra-long splined body to prevent slippage and can also be used to remove and install Shimano disc brake rotors. The FR-5 requires the use a chainwhip tool (sold separately) to prevent the cassette from turning during lockring removal.

The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs. -Utilizes a 12mm guide pin to stabilize the tool during use - Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings

Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool

A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings

The FR-5GT specifically allows you to remove and install cassette lockrings from thru axle hubs. - Utilizes a 12mm guide pin to stabilize the tool in use - Fits 12-spline cassette lockrings from Shimano , SRAM, SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings

Park's Compact Crank Puller is used to remove Shimano Octalink, ISIS Drive and square-taper cranksets. It includes 2 rotating tips (16.3 and 11.3mm) to make the job easy. This is a great tool for your travel and home tool kit.

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

What's your seatpost size again? Park's Digital Caliper accurately measures seatposts, head tubes, bearings, spoke diameters, etc. It's a precision instrument built accurate to 0.01mm with a stainless-steel mechanisms and a rugged composite body. The tool’s ability to measure in metric, decimal inch, and fractional inch makes it an indispensable home workshop tool. It features an automatic shut-off and comes with a protective sleeve and the battery.

Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.

Many new bikes do not include pedals. The DP-1 Dummy Pedal quickly installs to take the place of a pedal when making adjustments during the assembly of these bikes. Use of the DP-1 is much quicker than threading a pedal into the crank and then unthreading it after the bike is assembled.

The Park FR-3 Freewheel Remover fits SunTour four-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

The Park FR-4 Freewheel Remover fits Atom, Regina, splined Zeus and some Schwinn-approved freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

The Park Tool Fold-Up Hex Wrench Set combines 4, 5 and 6mm hexes, a flat blade screwdriver and a T25 Torx compatible driver into one convenient fold-up tool. Its multi-position composite handle is comfortable, lightweight, slip-resistant, and 40% stronger than steel handles.

The Park Tool FWS-2 Fold-Up Wrench Set combines all the popular hex and Torx compatible wrench sizes of the AWS-10 and TWS-2 into one convenient set. The multi-position shop grade fold-ups are comfortable, lightweight, slip-resistant, and 40% stronger than steel handles. Made in USA.

Park's Hex Wrench Set offers all the popular Allen wrenches (1.5, 2, 2.5, 3, 4, 5 and 6mm) in a convenient fold-up unit. The tool tips are chamfered for a positive grip and the one-piece fiber-reinforced-resin handle is light, comfortable, slip resistant and 40% stronger than steel.

Park's Hex Wrench Set offers 3, 4, 5, 6, 8, and 10mm Allen wrenches with chamfered tips for a great grip and easy use. The one-piece fiber-reinforced-resin handle is light, comfortable, slip-resistant, and 40% stronger than traditional steel handles.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.